Issues with stepping in debugger.
15 posts
• Page 2 of 2 • 1, 2
Re: Issues with stepping in debugger.
Whatever this issue is, it appears to be getting worse. I now need to hit resume 10+ times to get code executing again.
- DanTalash
- Posts: 23
- Joined: November 25th, 2015, 6:19 pm
Re: Issues with stepping in debugger.
Hi Miroslav
Can we do a Teamviewer (or something) else session where you could inspect the environment and get down to the issue?
BrW
Can we do a Teamviewer (or something) else session where you could inspect the environment and get down to the issue?
BrW
- WaldemarHasz
- Posts: 22
- Joined: December 3rd, 2017, 9:14 pm
Re: Issues with stepping in debugger.
Hi,
That's a good idea. Let's plan this. When would it suite you? you can just send me an email to miloslav at devsense.com
Thanks,
That's a good idea. Let's plan this. When would it suite you? you can just send me an email to miloslav at devsense.com
Thanks,
Miloslav Beno │ DEVSENSE s.r.o. │ @miloslavbeno │ miloslav@devsense.com
-
Miloslav Beno - Posts: 1252
- Joined: January 7th, 2012, 8:36 pm
Re: Issues with stepping in debugger.
Hi Miroslav
Thanks for helping out. The email was send.
BrW
Thanks for helping out. The email was send.
BrW
- WaldemarHasz
- Posts: 22
- Joined: December 3rd, 2017, 9:14 pm
Re: Issues with stepping in debugger.
Hi guys,
With Waldemar we've been able to find out the cause of the issue.
In his solution php framework gets requested a lot, so it's possible that even 50 requests gets attached to the Visual Studio at once. So at first sight pressing F10/F11 is not doing what is supposed to do, but it is... it's sending step signal to one process and runs other processes, so it may happen that other process gets breaked on the same breakpoint before the original process finish stepping.
Current solution is to use commands for Stepping for current proccess instead of F10/F10.
- Step Into Current Process (typically Ctrl + Alt + F11)
- Step Over Current Process (typically Ctrl + Alt + F10)
- Step Out Current Process (typically Ctrl + Shift + Alt + F11)
Please check the documentation https://docs.devsense.com/debugging/stepping#stepping-when-debugging-multiple-requestsprocesses
Thank you,
With Waldemar we've been able to find out the cause of the issue.
In his solution php framework gets requested a lot, so it's possible that even 50 requests gets attached to the Visual Studio at once. So at first sight pressing F10/F11 is not doing what is supposed to do, but it is... it's sending step signal to one process and runs other processes, so it may happen that other process gets breaked on the same breakpoint before the original process finish stepping.
Current solution is to use commands for Stepping for current proccess instead of F10/F10.
- Step Into Current Process (typically Ctrl + Alt + F11)
- Step Over Current Process (typically Ctrl + Alt + F10)
- Step Out Current Process (typically Ctrl + Shift + Alt + F11)
Please check the documentation https://docs.devsense.com/debugging/stepping#stepping-when-debugging-multiple-requestsprocesses
Thank you,
Miloslav Beno │ DEVSENSE s.r.o. │ @miloslavbeno │ miloslav@devsense.com
-
Miloslav Beno - Posts: 1252
- Joined: January 7th, 2012, 8:36 pm
15 posts
• Page 2 of 2 • 1, 2
Who is online
Users browsing this forum: No registered users and 42 guests